TechniqueHomeowners & Pros

How to Install a Blum AVENTOS HK-S Stay Lift

The AVENTOS HK-S is Blum's compact stay lift for a lift-up door on a small or shallow wall cabinet: two lift mechanisms, one on each cabinet side, locate on two pins and three screws. This guide shows how to pick the set by power factor, the parts to order by Blum part number, the pin and screw positions and the steps in order, for cabinets from 186 mm (about 7-11/32 in) to 610 mm (about 24 in) high.

Doors, Drawers & FrontsUS catalog, in inches and millimetersUpdated November 2026Download the PDF

AVENTOS HK-S at a glance

Cabinet HeightFrom 186 mm (about 7-11/32 in) to 610 mm (about 24 in) outside height, up to 1828 mm (about 71-15/16 in) outside width
Inside SizeInside height at least 150 mm (about 5-29/32 in), inside depth at least 163 mm (about 6-7/16 in), or 240 mm (about 9-15/32 in) with a visible wall hanging bracket
SizingPower factor = cabinet height (in) x door weight including double handle weight (lb)
Opening Angle107 degrees, with optional stops at 100 and 75 degrees
Cabinet SideTwo locating pins and three wood screws Ø4 x 35 per mechanism
OptionsTIP-ON fits the HK-S

From Blum AVENTOS catalog p.9, 50, 47, 49.

Who this guide is for

A homeowner or small workshop hanging a lift-up door on a small or shallow wall cabinet from 186 mm (about 7-11/32 in) to 610 mm (about 24 in) high. The HK-S needs an inside depth of at least 163 mm (about 6-7/16 in) and an inside height of at least 150 mm (about 5-29/32 in).

What you need

Order one lift set by power factor, and the door mounting plates for your door.

Blum Part NumberWhat It IsHow ManyYour Choice
20K2B00.06, 20K2C00.06, 20K2E00.06AVENTOS HK-S lift set, chosen by power factor: 2 lift mechanisms, covers, 2 branding elements and wood screws Ø4 x 35 (qty 6)1 setDark gray (TGR), Silk white (SW) or Light gray (HGR)
175H3100Door mounting plate, screw-on, for wooden doors and wide aluminum frames1 per lift mechanism; see the maker's instructions
177H3100EDoor mounting plate, EXPANDOin place of 175H3100
177H3100Door mounting plate, knock-inin place of 175H3100
175H3F00Door mounting plate with bracket for large overlay five-piece doorsin place of 175H3100
20K4A00A02Door mounting plate set for narrow aluminum framesin place of 175H3100
20K7A41Opening angle stop, 100 degrees, dark gray (TGR)Optional: see the maker's instructions
20K7A11Opening angle stop, 75 degrees, dust gray (R7037)Optional: see the maker's instructions
20K6A01Frame mounting bracket set for a face frame cabinet: M4 x 30 lift mounting screws, qty 121 set, for a face frame cabinet

From Blum AVENTOS catalog p.47, 48, 49, 64. Finishes and colors are your choice; the table names them as Blum prints them.

Blum notes that the smallest set, 20K2B00, holds one unsprung mechanism with no tension adjustment and one sprung mechanism. The TIP-ON version of each set ends in T: see the TIP-ON guide.

Jigs and tools that make it easier

Blum's catalog shows a universal individual template for the lift's cabinet side, and the two locating pins of the HK-S need holes there. These jigs help when you work by hand.

Blum Part NumberJig or ToolWhat It Does Here
65.1051.02Universal individual template, with the 5 mm (about 3/16 in) drill bit DB-5mmMarks and guides the two locating pin holes and the screw positions in the cabinet side.
ZML.0040.02Universal drilling templateMarks and drills the front fixing positions on the door.
#2 POZI DRIVER#2 POZI driver, or POZI BIT #2X2 in a screw gun with a BIT HOLDERBlum says a POZI screwdriver, which is different from a Phillips, is the most crucial tool to make sure full torque reaches the mounting screws. It sets the tension and the cams.

From Blum AVENTOS overview p.1; Blum AVENTOS catalog p.67.

If you cut on a CNC router, you can drill these same positions from your own cut file, so the jigs here are for building by hand.

Sizing, space and limits

The HK-S is picked by power factor, from the cabinet height and the door weight. Blum counts the handle weight twice.

Power factor

Power factor = cabinet height (in) x door weight including double handle weight (lb)

Cabinet height in inches. Door weight and handle weight in pounds. The handle weight is counted twice, as Blum prints.

From Blum AVENTOS catalog p.47.

Clearance for a cornice or crown molding, with no opening angle stop

Y = FH x 0.29 - 15 + FD

FH is the door height and FD the door thickness, in millimeters. Blum's table heads this row Unsprung.

From Blum AVENTOS catalog p.51.

With the 100 degree stop

Y = FH x 0.17 - 15 + FD

From Blum AVENTOS catalog p.51.

With the 75 degree stop

A = FH x 0.26 + 15 - FD

From Blum AVENTOS catalog p.51.

Power Factor Ranges
Part NumberPower Factor FromPower Factor toOpening Angle
20K2B00.061944107 degrees
20K2C00.063588107 degrees
20K2E00.0684195107 degrees

Blum prints no inclusive or exclusive word for the end of a range, so read each range as running from its first figure to its second, and do a trial application near either end. From Blum AVENTOS catalog p.47.

Cornice Clearance X by Door Thickness FD
Door Thickness FDX
16 mm (about 5/8 in)70 mm (about 2-3/4 in)
19 mm (about 3/4 in)59 mm (about 2-5/16 in)
22 mm (about 7/8 in)49 mm (about 1-15/16 in)
26 mm (about 1-1/32 in)35 mm (about 1-3/8 in)

From Blum AVENTOS catalog p.51.

Blum recommends the more powerful lift mechanism for applications in overlapping ranges, and a trial application when you are in a borderline area of a mechanism's power factor range.

Blum prints: "The power factor can be increased by 50% if you use a third lift mechanism."

The minimum gap (MF) between doors is 2 mm (about 3/32 in), and the top panel thickness SOB for the pin drawing is 22 mm (about 27/32 in) at most.

Worked exampleA cabinet 15 in high and 30 in wide

The door weighs 3.2 lb and the pull weighs 0.2 lb.

  1. The pull counts twice: 2 x 0.2 = 0.4 lb
  2. Door weight including double handle weight = 3.2 + 0.4 = 3.6 lb
  3. Power factor = 15 x 3.6 = 54
  4. 20K2B00.06 ends at 44, 20K2C00.06 runs from 35 to 88 and 20K2E00.06 starts at 84, so only 20K2C00.06 holds 54.

Order lift set 20K2C00.06 and door mounting plates 175H3100, one for each lift mechanism.

Where two ranges overlap, Blum recommends the more powerful mechanism.

From Blum AVENTOS catalog p.47.

Drawings and positions

Every drawing below is ours, drawn to scale from the figures Blum prints and named with its source page. The letter on a dimension line points to the table under the drawing.

Top edge Front edge A 37 B 64 C 74
Locating pin holes in the cabinet side. Drawn by CabDesign after Blum AVENTOS catalog cme106254, p.50. Two holes, Ø5 mm (about 3/16 in) and at least 5 mm (about 7/32 in) deep, in a row 74 mm (about 2-29/32 in) below the cabinet top, the top face of the top panel, measured from the front edge back. On a cabinet whose top panel sits on the sides, take the top panel's thickness off to measure from the side's top edge. The top panel is at most 22 mm (about 27/32 in) thick.
LetterFigureIn InchesWhat It Measures
A37 mmabout 1-15/32 inFront edge to the first pin hole
B64 mmabout 2-17/32 inFirst pin hole to the second
C74 mmabout 2-29/32 inTop edge down to the row of pin holes
Top edge Front edge A 125 B 53 C 35.5 D 37 E 106
The three fixing screws in the cabinet side. Drawn by CabDesign after Blum AVENTOS catalog cme106254, p.50. Three wood screws Ø4 x 35 for each mechanism. Every figure is measured from the front edge, or down from the cabinet top, the top face of the top panel. On a cabinet whose top panel sits on the sides, take the top panel's thickness off to measure from the side's top edge.
LetterFigureIn InchesWhat It Measures
A125 mmabout 4-29/32 inFront edge to the rearmost screw
B53 mmabout 2-3/32 inFront edge to the middle screw
C35.5 mmabout 1-13/32 inFront edge to the lowest screw
D37 mmabout 1-15/32 inTop edge down to the upper two screws
E106 mmabout 4-3/16 inTop edge down to the lowest screw
Top edge of the door A 78 - F B 32 C 12.5 + SFA
The door plate screw holes. Drawn by CabDesign after Blum AVENTOS catalog cme106254, p.51, for wooden doors and wide aluminum frames, with the gap F and the side overlay SFA drawn as zero. Narrow aluminum frames use a different pattern: use door mounting plate set 20K4A00A02 and follow Blum's page 51.
LetterFigureIn InchesWhat It Measures
A78 mm - Fabout 3-1/16 in - FTop edge of the door to the upper hole, less the gap F
B32 mmabout 1-1/4 inUpper hole to the lower hole
C12.5 mm + SFAabout 1/2 in + SFASide edge of the door to the holes, plus the side door overlay

Steps, in order

  1. Pick the set by power factor. Multiply the cabinet height in inches by the door weight in pounds, counting the handle weight twice, and choose the set whose range holds the answer. Where two ranges overlap, choose the more powerful set.
  2. Check the space. The inside height is at least 150 mm (about 5-29/32 in) and the inside depth at least 163 mm (about 6-7/16 in), or 240 mm (about 9-15/32 in) with a visible wall hanging bracket. The cabinet is at most 610 mm (about 24 in) high. Check the cornice clearance with the formulas above.
  3. Prepare a face frame cabinet. On a face frame cabinet, block the frame out flush and use frame mounting bracket set 20K6A01, which needs a recess of at least 12.5 mm (about 1/2 in).
  4. Bore the locating pin holes. In each cabinet side drill the two Ø5 mm (about 3/16 in) pin holes at least 5 mm (about 7/32 in) deep, at the positions in the first drawing. Template 65.1051.02 helps.
  5. Fit the lift mechanisms. Seat each mechanism on its two locating pins and fix it with three wood screws Ø4 x 35 at the positions in the second drawing.
  6. Fit the door plates. Fix the door mounting plates to the back of the door at the positions in the third drawing, with two wood screws (606N or 606P) per side.
  7. Fit the opening angle stops, if you use them. Stop 20K7A41 limits the opening to 100 degrees and 20K7A11 to 75 degrees. Fit them as Blum's instruction sheet shows.
  8. Raise the arm with caution. Stand at arm's length and raise the arm. Blum says not to remove the plastic tab until just before attaching the door, and not to push the arm down or leave it down.
  9. Clip on the door. Click the CLIP mechanism of each arm onto its door plate.
  10. Set the tension. Use a POZI driver, or a POZI bit in a screw gun, on the tension adjustment until the door balances.
  11. Make the three adjustments and snap on the covers. With the POZI driver adjust the door's side, depth and height cams, plus or minus 2 mm (about 3/32 in) each, then snap on the cover plates.
  12. Remove the mechanism before moving the cabinet. Blum says to remove the mechanism before installing or removing the cabinet.

Check before you finish

Common mistakes

From Blum AVENTOS catalog p.50, 67, 47, 64; Blum HK-S instructions.

Free toolCheck Your Numbers

Enter your cabinet and door in inches or millimeters, and the Blum AVENTOS Calculator gives the part, its power factor and every hole, each cabinet figure measured from Blum's own line and from the side's top edge.

Open the Blum AVENTOS Calculator

What Blum's sheet decides

These details are not published in the Blum documents this guide is written from, so this guide leaves them out. Read them on Blum's own sheet for your part.

Frequently asked questions

How do I pick an AVENTOS HK-S lift?

Multiply the cabinet height in inches by the door weight in pounds, counting the handle weight twice, and choose the set whose power factor range holds the answer: 20K2B00.06 from 19 to 44, 20K2C00.06 from 35 to 88 or 20K2E00.06 from 84 to 195. Where two ranges overlap, Blum recommends the more powerful lift mechanism.

What size cabinet does the HK-S need?

An inside depth of at least 163 mm (about 6-7/16 in), or 240 mm (about 9-15/32 in) with a visible wall hanging bracket, and an inside height of at least 150 mm (about 5-29/32 in), in a cabinet up to 610 mm (about 24 in) high.

How far apart are the HK-S locating pins?

The two Ø5 mm (about 3/16 in) holes are in a row 74 mm (about 2-29/32 in) below the cabinet top, the top face of the top panel: the first is 37 mm (about 1-15/32 in) from the front edge and the second 64 mm (about 2-17/32 in) further back.

How many screws hold each HK-S mechanism?

Three wood screws Ø4 x 35. The set includes six for the two mechanisms.

Does the HK-S take TIP-ON?

Yes. Each set has a TIP-ON version whose part number ends in T. See the TIP-ON guide.

What is the opening angle of the HK-S?

107 degrees. Optional stops limit it to 100 degrees (20K7A41) or 75 degrees (20K7A11).

How CabDesign picks and sizes this

CabDesign sizes a lift-up front on the AVENTOS HK-S from the same printed Blum tables used in this guide. It reads the cabinet height, the door weight and the pull weight, counts the pull twice, picks the lift set and puts its part numbers, and the door mounting plates, on the project's buy list.

Try it

Size it the same way in the Designer

Pick a lift-up front, enter the door weight, and the Designer reads the same printed tables.

Open the Designer

Sources and references

  1. Blum AVENTOS catalog cme106254, LIT.AVT1001.08.26 (opens in a new tab), blum.com/file/cme106254_ep_dok_bus (ranges, part numbers and drawings)
  2. Blum AVENTOS program overview cme115842 (opens in a new tab), blum.com/file/cme115842_td_dok_bus (templates for each lift)
  3. Blum AVENTOS HK-S assembly instructions (opens in a new tab), blum.com/aventos-hks-assembly (the order of assembly and the arm warnings)

AVENTOS, SERVO-DRIVE, TIP-ON and BLUMOTION are names of Blum. This guide is independent: it is written by CabDesign and Blum has not reviewed it.

Blum's own instructions win if they differ, and Blum may change its parts without notice.

A CabDesign guide. Browse all guides.